HDD prices for NAS and NVR are a real pain.
If you're interested, I can describe the equipment topology, share photos of the rack, etc.

Hey Everyone,

I recently wantes to purchase the Unifi UPS 2U but Noticed Ubiquiti charges 25€ (~28 USD) "Memory Surcharge".

I completely understand why they implemented this system rather then raising the prices outright.

But why would they do it on a device that does not have any meaningful amount of Memory?

Is there a way to correct it?

Thanks!

Edit: I know that it has some ram 🙄 but the amount is not specified i am guessing ~256mb or even less. That doee NOT justify charging 25€ extra.

Attached are photos of a client site. It is a residence approx 4200sqft. Their primary complaint is WiFi feels a bit slow at times, leading to YouTube buffering and whatnot. When I look on the backend everything seems perfectly fine, except a low percentage of tx retries. What do yall think might be the issue?

6gh disabled last night to keep signal strengths high.

Edit: how do I add photos?? Grr
DNS has been updated per recommendation to Googles exclusively.

I think the culprit maybe that one of the APs, a U7 Outdoor is connecting at E rather than GbE. Time to replace a short cable…I

Final edit: turns out the issue really stemmed from an AP connecting at E, or what’s rated for 10mbps. 4K on yt requires 20, ideally 25mbps. Nonetheless I did suspect AP overcrowding might’ve been contributing as well. In the end with y’all’s insight I tackled 2 different issues pertaining to the same network. Thanks to everyone that contributed!!!

Pros would go above the garage pointing to the driveway so the purple, and then the back corner of the garage area the pink line

A small wing of the company I work for has been slowly migrating away and we're excited to get their own network, and through some various tactics I convinced them to go this way with things.

Needless to say I'm very excited to play with new toys.

Also known as a rack not full of strictly Ubiquiti products.

Recently completed a network refresh and rack update with changeover to Ubiquiti. Other equipment throughout the house is (1) U7 Pro XG, (2) Flex Mini 2.5G (media stand, wife's office) and (1) Flex 2.5G PoE (my office).

Patch panels and UPS are pre-existing, re-purposed a rackmount.it RM-FR-T14 (with keystone swap to white) for UCG Fiber, filler plates and PDU are new. While it would have looked cool to be all Ubiquiti silver and I'm not against overkill, I had no interest in throwing away money just for looks.

OS2 SMF optics and cables are ipolex brand from Amazon (owned by 10Gtek, same exact stuff with different name on sticker) except for a Fibergaga industrial armored cable running through my attic for the Pro Max 16 PoE to Flex 2.5G PoE uplink. Only downside I've found so far with the ipolex/10Gtek optics is that I don't get any optical levels in the controller, even though these optics support DDM. They do perform as expected at 10G.

In the future, I will swap all my Wyze wifi cams to UniFi PoE and will add UNVR (or G2) and a second Pro Max 16 PoE as I'll need more ports than the single switch will provided. I could have met total port capacity needs after camera swap with a single Pro Max 24 PoE, but I opted to go down the two switch route as its less money spent upfront, and I have switch redundancy.

I just learned about these things, Matter being the home automation/IoT standard, and Thread being essentially an IP based networking for IoT devices over the non-Wifi 2.4GHz radio system that works with it.

Neat stuff.

Updates from Ubiquiti a few days ago, specifically the SuperLink Gateway HA, the new one, has a Thread radio setup (with the loss of Bluetooth support, as it would cause interference) and recently the addition of pairing codes for Matter device awareness. The next thing they mention in the update is "For the first time, visualize IP and Thread devices together in UniFi Topology, with custom alerts and powerful tools for troubleshooting connectivity." suggesting continued Matter over Thread support.

In terms of implementation of Thread, the newer Apple Home... stuff, supports this type of connectivity. The brand "eve" of IoT home automation devices operates on this type of connectivity. A few other big companies have or are developing systems that support these standards.

So, the proprietary SuperLink standard is still ISM band, but on the baby-monitor-band (915MHz) rather than actual WiFi (2400MHz/2.4GHz). About as much data as you can pack in to bandwidth without a license or being wifi/2.4GHz. A benefit is you can encrypt it over air legally, which is not the case with many other open or available radio bands. And the Matter over Thread is essentially the same type of "baby monitor band" style of use, but is in the 2.4GHz range, and can therefore pack way way more data. The IPv6 base of the system, I would suppose, means that there is some level of encryption/handshake/privacy? Similar to the benefit of simple encryption over 915MHz.

I'm really eager to see how home automation and IoT connectivity develops through these standards and systems, but I'm also very curious what everyone thinks about these moves. Will it work? Will it be awesome? In outdoor settings, will connectivity go out when it rains really hard? Will this help support scientific data collection efforts like USGS water flow data and other sensors?

What other higher-data processes do you want to see work on these systems? What type of devices would integrate well on these standards with the Unifi ecosystem for home and enterprise/campus deployments?

What do you think?

EDIT: A lot of good comments from different sides of the aisles. I personally was considering a top-down, all Unifi network, including cameras and entry sensors/other security and home sensing, but I was personally waiting to pull the trigger on getting sensors and the SuperLink Gateway, since the new gateway might be really cool. But, I am considering that I should look more widely other companies producing different types of sensors... lots of them cheaper, surely, and perhaps just as good at connecting to any network with all the new communication protocols and radio systems that support them.

Had another thought, regarding Reticulum... sort of like Meshtastic/MeshCore communicators, that is a system that operates on 915MHz, but can also utilize 2.4GHz WiFi and Bluetooth, and potentially other methods to communicate. As far as I can tell it's kind of terrible and not built out and it's kind of open source, so probably not stable as it stands, but the idea of cross-device, cross-system communication to build a unified network is compelling and feels tangentially related to the 915MHz/2.4GHz non-wifi ISM band activities that these home automation-IoT companies are doing. There is so so so much 2.4GHz equipment, radios, antennas floating around, it would be almost stupid to not reuse them for something modern. Plus we all need higher fidelity WiFi sensing in our lives :)

Got the home setup cleaned up and everything tucked into a 15U cabinet. Matching silver gear, short patch cables, and just enough room left to make more questionable financial decisions.

The setup:

UniFi Pro UniFi Power Distribution

Pro Max 16 PoE switch

UniFi Dream Machine Pro SE

AC Infinity rack cooling

UniFi UNAS Pro 8 with 4 x 24TB Toshiba N300 Pro drives

Two U7 Pro XGS access points, mounted elsewhere

Eufy NVR and Cameras

HP laptop running Ubuntu, hosting my AI assistant, home assistant, Immach, Jellyfin and other home lab things.

Internal rack air stays around 20–24°C. Currently using it for networking, cameras, and self-hosted photo storage, with a personal Netflix setup on the to-do list.

Pretty happy with how it came together. Rate the rack, tell me what you'd change.

Is that too much the ask?

I'll try to keep this concise, but last night my wife and I heard a voice in my kids room (attached video) through our intercom. Completely freaked me out, more so because I believe the only place it could have come from is the UniFi Cameras.

Ive been looking at logs and sending Claude through them and everything is coming back clean.

Kids Room Devices

• G3 Instant (opposing side of the room)
• G4 Instant (opposing side of the room)
• Google Home Mini
• Sonos Move
• Intercom (Model DM111/DM111-2)
  

Tech Stack in the Mix

• UNVR - Remote access enabled
• UDM Pro
• Proxmox
• Nginx Proxy Manager
  • Proxy to Home Assistant
• Home Assistant
  • Music Assistant
  • UniFi Protect
  • Apple Music
• Sonos

Events

• The intercom has two sides; a child side (microphone) and parent side (speaker). We heard the voice through the parent side in our bedroom.
• I pulled up the camera's and rolled back to when I heard the sound and listened again, and the voice is there, in the room. I thought maybe my parent side monitor just picked up a neighbor, but I confirmed through the cameras it was in the room, on the other side of the house, 2nd floor.
• The Sonos speaker was actively playing rain sounds.

Investigation

• The voice was not TTS as you can hear.
• Confirmed no network traffic to the Google Home Mini, no chime, no broadcast message
• Listened to the rain sounds on my phone to see if there was a voice in the audio; nothing there.
• To my knowledge, Sonos doesn't support dropping in and speaking through the speaker, no chime no broadcast.
• The baby side of the monitor in the room only has a microphone, no speaker per the manual. I also opened it and confirmed no speaker inside the baby side of the monitor.
• Ran log checks against every authentication into nginxproxy manager, the udm pro, home assistant, unvr and even pulled logs from the cameras themselves; confirmed no stream was played through the camera. No connections into anything other than my own.
• Confirmed all logins under my account, and the wifes account for unifi were from our known IP's, local network and known public IP address / devices.

Normally, seeing logs and confirming no strange behavior would put me at ease, but that still doesn't answer the question of, where the hell did the voice come from??

Flair: whine / complaint, though I'm not really bothered. Just hoping some of the following come to fruition.

I've been on the cusp of moving off my current home security "solution", and have stopped myself from pulling the "buy now" trigger a couple of times. FWIW, here's my list of needs and wants that would nudge me over the line.

Need:

• Keypads with easily distinguished panic buttons (e.g. assignable to Fire / Medical / etc.). I'm open to SuperLink or PoE. On second thought: while I hate adding more battery-powered devices, retrofitting PoE to the install locations realistically isn't going to happen.
• Support for hardwired smoke and CO alarms. This seems like it may be coming, per the current battery-powered option's FAQ: *"Future products will accommodate a wider variety of installation scenarios and direct interconnection between smoke alarms."* I'll buy 6 of these if and when they ship.
• The SuperLink Gateway HA to ship. I need the LTE backup.

Want:

• The Alarm Hub Kit sold without the bulky enclosure, or at least supported outside it so it can be fitted into other cabinets (the FAQ specifically says this isn't supported). Ideally the tamper detection could be fitted to third-party enclosures, so I could put it in something like a 42" On-Q in-wall enclosure alongside other equipment and fit the sensor to its door.
• An outdoor-capable SuperLink thermal sensor, with a definable rate-of-rise or maximum-temperature trigger. These would go in uninsulated garage spaces where multiple EVs charge.
• A purpose-built option for exterior corner-mounted cameras. Ideally one PoE install giving 270° of coverage. I don't want a single stitched stream, especially if it costs net resolution; I want one compact enclosure that leaves no blind spots. More or less a more discreet, compact AI Multi-Sensor 4 with one less camera.
• A Protect-integrated garage door controller along the lines of ratgdo / Konnected / Tailwind.

What I really want (but don't expect)

I run both Home Assistant and Scrypted to bridge into Apple Home. I don't want or need family and some guests inside UniFi apps; it's just easier this way for some of my "end users". The tumbleweeds drifting across Ubiquiti's sad, lonely public GitHub are a massive missed opportunity. Shipping these so they're "natively" installable on Unifi gear, but opening up the pieces under a suitable OSS license (with Ubiquiti retaining governance, SDLC), would let the community build and maintain them beyond what Ubiquiti seems inclined to invest in directly. Roughly prioritized:

1. Native HomeKit Secure Video for Protect cameras. This would remove the need for Scrypted or similar bridges entirely.
2. The Alarm Hub as a HomeKit security system. Arm and disarm from the Home app, Siri and Apple Watch, with no bridge.
3. Protect sensors as HomeKit accessories (motion, contact, leak, temperature), with no Home Assistant hop. Same for the siren and doorbell presses.
4. Protect smart detections as HomeKit events (person, vehicle, package, animal). Detection would run on Protect rather than on Apple TV and HomePod home hubs.
5. Build on Network 11's Matter visibility. Make UniFi gear a Thread border router, and route Matter between VLANs, so Matter devices can live on an IoT VLAN without sharing a segment with my home hubs.
6. Wi-Fi client presence as HomeKit occupancy.
7. Apple Home Key on UniFi Access readers and locks.
8. HomeKit-enabled router support. Per-accessory isolation and cloud allowlisting set from the Home app, so HomeKit devices can share the hubs' network without per-device firewall rules. Less important to me, since I'll keep a separate IoT VLAN for non-HomeKit devices regardless.
9. A stable, versioned, documented public Protect API, so third-party bridges stop breaking with Protect updates.

I took a trip last month and flew on America airlines. With my normal utr it was able to connect to aainflight and I was successfully able to broadcast my SSID and use it. Unfortunately I left it on the plane by mistake.

Fast forward and I now have the utr-lr. Just took another flight on American Airlines again. Tried connecting to aainflight again this week and it kept failing when trying to get to the captive portal using the utr. It could never resolve the aainflight.com web site. Using my phone without the utr, I was successful in connecting to captive portal but the utr never was able too.

Then I made it to my hotel. Here I’m also unable to connect to the captive portal. It just opens captive.apple.com with a successful message but nothing more.

In both cases with the utr-lr, the captive portal never opens. Using my phone I can directly connect and authenticate to the portals without the utr-lr but so far never using the utr-lr.

What am I doing wrong? I’ve attached photos from the hotel while I’m still here.

Thanks for any help.

Just upgraded from UNAS 2 to UNAS Pro and am thinking I may have outgrown the mini racks and could move to a full size rack cabinet.

Maybe a 19inch rack cabinet and a shelf inside that the mini rack could sit on. Anyone done anything like this?

I have a client who has an existing Comlit doorbell/displays that he wants to get rid of. We just installed 3 ubiquiti cameras and figured a doorbell is the best solution for this. The thing is I cant figure out a good way to display the feed when someone rings the bell. Ideally we can have 2 way communication as well. Is iPad on the wall the way?

Enterprise technology. Without the enterprise tax.

Meet UniFi: ui.com

Setting up a management VLAN, putting the switch and AP there - does the gateway get put there too somehow?

Hey all. I brought one of these to play with and use as a cheap wifi ap. (air cube air max ac)

I've tried to configure it but it's not giving me a default wifi. Set up as per many YouTube videos with a micro USB power and turned On.. it should give me a default wifi network and then use the app to configure..

any ideas? I've tried to reset it a few times..

I have had a few people mention the doorbell is running very hot when touched.

Not got anything to measure it with but doesn't seem normal considering it's a cloudy grey day with no direct sunlight.

Anyone else have same issue?

Just got the Superbox and BlueTV not working. BlueVOD works fine. Connecting the SuperBox to my hotspot works fine. Anyone figure out what is blocking TV? Do I need to create a rule?, turn off ad blocking? UDM Pro. Latest firmware. Appreciate any assistance.