Finally found a CRT I really loved, a Sony KV-27FS100, and decided to create a Nintendo-specific corner for cozy, nostalgic gaming.

Wii and GameCube games look phenomenal over component. SNES and N64 are running composite. Should I invest in S-Video cables?

Shoutouts to Justin Wong.

Original link: https://www.youtube.com/watch?v=KqgURiTQZSQ

Modern games look incredible on CRT monitors, they’re sharp (even at lower resolutions) and have perfect motion clarity. The monitor I’m using is the Philips 107E21

I found it on the side of the road with a dell E773c both of their VGAs cut. The Dell is dead after using it for a bit (for now). I recapped like 80% of this monitor and cleaned it just in case.

It's a very strange monitor as it doesn't have a g2 on the flyback nor anywhere on the actual board and neckboard. It also has a chip socket for the main OSD I believe. Kinda looks like it needs to have it programmed to change the value which sucks since looks like it's up a bit. Also the entire back of the tube is lined with a RF shield. Looks almost bullet proof how covered it is. The deeper menu has some black level adjustments that seemed to help a bit. It has a "self diagnosis" function but doesn't really do anything of value.

The picture is pretty snazzy and I hope it lasts me longer than the other monitors I've given this much love.

Wish me luck haha

What can you guys tell me about it?

Thinking of keeping this one on my collection

I have an unmodded Xbox 360 S connected to my Sony PVM-20M4U with a component cable and use it with the official remote control. Plex stopped working for me this year, but the 360 still supports:

• DVDs
• MP4 (H.264) or AVI via USB
• Netflix
• YouTube

Do any of you guys have both a PS3 and an Xbox 360? If so, how do they compare?

I put this together for my wife’s birthday last month. Picked up the PS2 shortly after obtaining the monitor. Replaced the laser as it was weak and having trouble playing some games and DVD’s. Console outputs RGB over SCART and is software modded to output RGB for DVD. For sound Sony SRS-A202 shielded stereo speakers.

It’s been fun in the weeks after hunting for ps1/ps2 games and 4:3 full screen DVD’s. I even found my original PS1 memory card with my 27 year old save files!

Always wanted this little Trinitron and it definitely lives up to what I've heard about it! The symphonic had its cord cut but soldering a new one on wasn't too hard. It has an issue with the composite input, I think it might just be bad solder joints on the RCA plug since RF works fine. If anyone knows what the issue is let me know! It's VHS player also just ejects the tape after inserting it, might be a mode switch issue but I'm not sure. Either way happy to have it

Got it for the free. Still works great. Few cracks in the plastic here and there but it’s whatever.

Got her off the side of the road. Model number CX32G60. July 1997. Modded my gamecube for this lol.

I was finally able to connect the SuperStation One to my CRT television, thanks to an affordable Mini-DIN 10 to SCART RGB cable. I am thrilled to finally play NTSC games without needing to modify my PAL consoles. After filling the SD card with a variety of games, I am currently enjoying some Neo Geo fighting games. Such a nice piece of hardware!

Hello crt community!

I was wondering, what should i know before i RGB Mod 2 sony tv

A bit of info, i was handed down 2 crts. And for my surprise they were two sony trinitrons, one black with a curved screen and the other one was silver with a bit flatter screen . So i was wondering, can they be RGB moded, so i got into the rgb mod rabbit hole and ended with more questions than answers, so thats why im here.

How hard is it to perform? i have calibrated the focus and G2 on a CRT in the past so I'm a bit less worried about working on them. Also have experience soldering. So thats not an issue.

Second, can i have both VGA and scart? Because i have a pc with CRT EmuDrivers and would love to use it with those tvs instead of my actual one (I have a Philips something something, pc vga -> diy transcoder -> component).

Third.

Is it okay to diy RGB scart cables? What should I have in mind when doing it? Because in my country scart is not a thing in any set. As far as I remember. I have in mind doing cables for a PS2 to scart for RGB.

Edit: Would love some recommendations to do the anode cap seal. Because i suspect some leak, i was shock (it was a soft one) while touching the plastic on the top of the tv when i picked it up after testing it the first time i saw them

And that should be all! Now I'm going to attach the picture i have of the sets to help with identification. Gray one says chassis BA-5 the black one dosent says but i suspect its a Chasis BA-4 and in the inside has a KV-21SE80 sticker, let me know if more data its needed

Edit: thanks everyone, I'm doing some more research before committing but all information was very useful. Really thanks. Would love to post when i completed the mod.

I've gone through so much back and forth with this poor monitor and refuse to give up until it's able to work flawlessly. Me and my friend recapped the A board and I sent it to a repair shop; still it has these irregular video artifacts.

I sent another similar video to a different repairman in my area and here's what he said:

"Ive never seen this tbh... i would suspect a power supply or deflection circuit issue. It might be IC related."

They recommended trying to locate another monitor to trade boards, not sure if that's easier than trying to fix the problem directly. The video signal has always had problems but never like the video I included in this post. Not sure if that means it's getting worse or not.

Any help is appreciated, I'd hate to admit defeat but it's definitely felt bleak recently.

My trinitron has worked perfectly before this, I have my NES connected to the front inputs by composite, and now suddenly the image looks like this. What is causing this and how do I fix it?

I recently got my hands on a Panasonic ct27d11e. I believe that the degauss thermistor has gone bad since I suddenly ran into a fairly severe color purity issue, and my tv tries to degauss every single time it powers on. Do I need to find a specific thermistor/posistor, or do I only need to find one that meets certain requirements? Any help is much appreciated!

This crt I have had when I was around 5 years old, at most around 2012

I know it might be an impossible ask, but this crt, I was curious to find if I could possibly buy one like this again, since this was one was thrown away about 10 years or more ago, I don't remember much of it, only that it appeared in a video my father made 18 years ago, and the only focus of the video was me and not the crt tv, so there were no good shots of it

I am unsure exactly of the age, since it was a hand me down from my grandfather to my father

So basically my question is, can you all try to find the exact model of a crt that's only really seen from a few bad angles? I don't even know the brand unfortunately, I do know it might have been 28 to 32 inch but that's only with looking at the perspective

For my homemade arcade cabinet I'm using a Sanyo C21TF26S. It didn't come with a component input from factory, so I did a little mod to add the input rebuilding the YUV stage of the circuit. I'm also using a homemade VGA to component transcoder. The image looks really good in comparison to composite, at least for me. The issues I'm facing now are two:
1- When there is white text or pronounced white lines, it leaves a black trail in the screen, and vice versa (black lines leave white trails). I wouldn't attribute this to the transcoder since it's a pretty straight forward and known schematic. I'd rather think that unbalanced inputs from my mod could be causing it.
2- The picture "deflates" at the top when it's dark and "inflates" when it's bright. It curves downwards at the top and recovers when the image gets bright. I don't really know how to describe this so I'll leave a video. I've read it may be the B+ voltage but I'm a little afraid of tinkering with it since I'm still a beginner in CRT's. https://youtu.be/l-_8pzveSu4

First picture is issue 1, second and third picture is the stage i had to rebuild in order for the YUV input to work.

If anyone knows what could be causing these issues and how to fix them I'd be really grateful. Thanks.