Please help guide a newbie.

So, I do quite a lot of variety of live PA gigs. Some live bands, some corporate dialogue gigs, etc...

Right now I'm building some JW Sound Solana speakers. I'll probably eventually add subwoofers but don't know which yet. Regardless, some DSP added into my system chain is going to be needed. Technically my Behringer Wing already can output channels separated and processed, but I simply can't trust that as I'll often reset the board for a new gig (then need to reconfigure all output filter settings/routings.

I also have a good-ish (Josephson Engineering) measurement mic that I usually run REW with, so I'd love to just run a room sweep and have the DSP correct things without me attempting to match curves.

So, is it more configurable to have dedicated signal processors like a DriveRack or t-racks or minidsp and then dumb amps? Is it safer to have the protection onboard the amp directly? If one is budget-constrained (slightly) does one setup pose higher costs?

I bought a custom fit box for my Jeep. Gladiator from his car came with two Skar Audio VS-12 D4 12-inch subwoofers. Blew them out so the company sent me some new ones but did not include any screws to secure it to the box. The box has metal pieces for the screws to go in but I can’t seem to find the right ones. Does anyone know which hardware works?

Hey guys, doing some digging before I start cutting wood. I'm building my first real system and want to start small and add to it.

Phase 1 is one Cubo Sub (the 18") loaded with a B&C 18TBX100 (8Ω, 6.2Ω min, 1200W nominal / 2400W program) and one Celestion CKT-TF1225 top (8Ω nominal, 6.5Ω min, 250W AES woofer, 400W EIA system). Phase 2 is a second sub and top, and later I want to add Cubo Kick 15s in the middle.

Use is backyard hangs and small gatherings, maybe a festival camp for 30-40 people. Not a concert rig, I just want it to sound good and not be underpowered. I'll run a miniDSP 2x4 HD for crossover/EQ and have a friend helping me tune with a mic. Planning to cross the sub around 80-90Hz and the top above that.

Where I'm stuck is amps. Budget isn't super tight (a few hundred over is fine) but I'd like to keep it in check:

- Crown XLS 2502 (open box, ~$539) for the sub, XLS 1002 for the top(s) later
- Behringer NX3000D (~$339) with the built-in DSP, or an NX4-6000 (~$469) to cover everything with 4 channels
- CVR D-1002 (~$699). A friend says plenty of people run these without issues

What I keep going back and forth on:
- Is the Behringer's listed 440W @ 8Ω real or just peak, and does it matter for a sub at my listening levels?
- Has anyone had Behringer NX amps die on them?
- Would you take the CVR over the Crown for subs?
- Should I use the 4Ω version of the TBX100 to get more out of the amp?

What would you run? Any gotchas with the Cubo Sub + TBX100 combo I should know about? Appreciate any help.

I'd like to build 2x 2-way tops (passive) to be used for small parties while traveling (PA). I am a house (primarily tech house) DJ. Planning to power with a Behringer NX1000D or similar when traveling by plane. Locally, will pair the tops with a sub or 2 that I would also build.

For the top cabs, I'd like to be able to carry them on, one each between my partner and I. Approximate max dimensions (each): 21" x 13" x 8" (this leaves room for padded bags).

Looking for driver recs (10" + 1"?).

I'm also looking for design recs. I'd like the drivers to be visible or have some other neat cabinet design that is both cool looking and functional.

Budget: $1250 but can go higher if I need to. I just don't want to spend a lot more unless I have to.

This will be my first speaker build. Thanks for your expertise!

A harsh belarusian psychedelic vibe. An event held in the back of a truck at -18°C.

Hello guys i got this 18 Sound 21lw1400 driver and as You Can See the yellow think i dont exactly know How its called ripped all around you should be able to See the Little gap and i thought in theory i whould be able to just Glue it back together im Not gonna give it its Full power annyway so i dont think it is going to rip do you think this whould be possible?
Thanks for helping :)

Five-way system: a 4590 coaxial driver at the top, with work currently underway on the horn.

I really like the sound of the paper 8-inch drivers in these tops compared to the super-fast, crisp, and somewhat harsh "plastic" mid-range section of the coaxial BMS 4590s (though lining the fiberglass horn with bitumen mats did soften that characteristic); the paper drivers offer a sound that is smoother, more "alive," and more spacious. I wonder if it’s possible to swap the HF drivers in the RS2H for something from BMS?

It’s certainly a bit tricky to phase-align them with the Paraflex without an all-pass filter, but I’m managing for now.

Ciao a tutti!

Non sono un totale inetto nelle creazioni audio DIY, ma non mi ritengo affatto un esperto! Dopo qualche progetto ed esperimento realizzato in totale autonomia, e di discreta qualità, mi sento abbastanza maturo per cimentarmi nel mio primo piccolo sound system. Voglio mettermi alla prova, imparare e per poi... molto probabilmente, alzare ulteriormente il livello.... (ma questa sarà un'altra storia!)

Ho bisogno di consigli, disegni, diagrammi e progetti per realizzare un piccolo sound system con queste caratteristiche per me TASSATIVE e irrinunciabili: - Configurazione 2.1: 2 canali stereo più 1 canale mono dedicato al subwoofer. - Dimensioni compatte: speaker enclosures facilmente trasportabili in un'auto familiare. - Low cost. - Estetica aggressiva e accattivante. - Documentazione disponibile: disegni quotati, misure, indicazioni tecniche e link a progetti esistenti.

Inoltre, considerando queste esigenze, quale sarebbe secondo voi la configurazione migliore? - Opzione (A): 2 vie per canale (woofer + tweeter) e subwoofer. - Opzione (B): 3 vie per canale (woofer + midrange + tweeter) e subwoofer. - Opzione (C): 1 singolo driver full-range per ogni canale stereo, più subwoofer. - Opzione (D): altre soluzioni eventualmente più adatte.

Apprezzo soprattutto progetti concreti e collaudati, con link, disegni quotati e indicazioni tecniche utili alla realizzazione.

Ringrazio anticipatamente tutti coloro che vorranno darmi una mano!

Edit: non sono anglofono. Io scrivo con la mia lingua madre e Reddit traduce automaticamente.

A Psy-trance setup: a pair of RS2H units per side and a pair of 15-inch Kubo Kick bins—delivering a fast, dry punch—though there are some issues to address, specifically the need to dampen a rather strong cabinet resonance at 158 ​​Hz. Let's see how four C2D 153 units handle it.

The cabinet turned out to be relatively complex to build. (4 units)

Hi all, before i send this off for repair (will be an open question i know) has anyone had this issue before? I load/ I limit channel limits flash on red and green on both channels, even at low volume, nothing has changed in my system, I have two 5000 vz's, ive tried different xlr cables and swapped power cables with the other 5000vz and still get the still get the same issue so I know its the amp. I know these can be prone to corroded internals but its been kept in dry storage for the 4 years of me owning it.

TIA

Hello!

I'm looking to buy 2 JBL D55 original double 15 inch scoops online, but after some researching I can't find any specifications on the drivers; I know they are probably mid 80's.

Does anyone know of any alternative 15inch drivers that I can place inside the legendary JBL D55 scoops?

Thanks in advance!

Considering buying some empty cabs, anyone know of a modern replacement driver?
Can’t find any info on original drivers other than they were PHL. 
Thanks ✌🏼

Hello friends, I'm a long time soundsystem appreciator, and I'm now pretty keen on the idea on starting my own journey in to building. I'm thinking of starting with a JMOD MEH, because they seem to be amazing, and I could scale easily with it.

My question is about the power of the amplifiers, I saw someone mention a standard thing to do is go for the driver's wattage rating X2 (nominal not continuous? Is that just another way of saying RMS and peak?) so as to have plenty of headroom and not send a potentially clipped signal to your speakers? Or is that more a concern for sub speakers, and a low-mid-High box like the JMOD less a concern?

Any info is helpful thank you bass friends!

Hey yall some people I know own this system and quite frankly don’t know what they are doing with it. I am also a novice and am building my own system but would like to help them tune this. I wish I had more info on the cabinets and driver so identifying them would be great. I think it’s some sort of W bin design on the sub and a cubo kick 18 mid with a MT121 on the tops but I’m not sure.

My follow up question to what are these cabs is what would the ideal crossover points be? 20-80 subs? 80-200 kicks? 200-20k tops?

Thank you for any help!

Cleaned off whatever playa was left though!

I have built a system thats consisting of 4x Super bass horn with 18” drivers and 4x hd kick horn with 15” drivers. I am looking for a good option to balance out the sound with mids and highs. Any recommendations?

Hello! I have bought 4x Wharfedale WLA28-XF

I’m wondering what cables I need? I’ve been looking for awhile I can’t seem to find any that’s looking to fit..

Hi all. Does anyone have any reviews or experience with the Celestion CKT-TF1020 tops? I wanna build a bass focused system for a friend and I’m planning on two cubo 18s paired with two Celestion CKT-TF1020 tops. Anyone have any recommendations or experiences with these? If so I’d love to hear anything and everything. I’m targeting 40–80Hz from the subs and about 80Hz up from the tops. Any amp recs or anything all around would be amazing!
Cheers

After 7+ months of weekends spent in the shop figuring all this stuff out I was finally able to make noise last night with my first system. Still have a lot of work to do, but couldn't be happier right now! Big thanks to Skylar at Subcurrent Sound for being my first point of contact into this world and for providing quality flat packs. Big thanks to everyone in this community for being kind, answering my questions, and providing guidance along the way.

Once I get a measurement mic and have some time, I'll measure/tune everything and post results.

Hi! I’m pretty new at this stuff and I wouldn’t mind a bit of help for this decision. Im looking to buy this used Crown Macro-Tech 12000i to drive 2 SKRAM’s (maybe four one day).

I read really good things about it but the price is only 2k$ Canadian which feels low from what I’ve seen and I’m wondering if I should be on the lookout for issues that would be pricey in to fix in the long run. Also what would be your tips and tricks on buying used amps (things to check and so on).

If you agree on it being a good buy, what would be a good DSP for it?

Don’t hesitate to give me as much info as you want. I’m all ears!

Thanks in advance!

3d models, print and paint by me

Hey all, made a little model of a rig i saw and can only dream of owning one day!
Really happy with how it came out, dm me for stl :)