Basically I do not want to run an ethernet cable 100 feet for wired connection. Am I able to buy some router and create a LAN for streaming at the same time? If so any advice on what router to purchase & how does the host PC distinguish between WiFi and the ethernet plugged into it? I’m able to stream using WiFi but the resolution isn’t the best so I’m hopeful I can do this.

Hey so I like to stream my games from my home pc to my iPad using moonlight and sunshine. It always worked ok for all of the games cause most of my games were from steam. Recently I bought a few games from gog and added them to steam but when I run the game the controller does not work properly, I can not select anything the selection just keeps going down and down. The games i used it with were a plague tale innocence and blood of dawnwalker did not work on both, although the controller is working correctly on other games like witcher 3 and control that I bought at the same time please help me to fix the issue. I really really appreciate you taking time reading this.

Using steam deck/steam machines as clients 99% of the time, both wired into 1gbps Ethernet. I read that the newest beta update of pyrowave allows up to 1gbps bit rate, but I've also read that 4k 60fps hdr 4:4:4 is a minimum requirement of 740mbps and easily spikes to 1.5gbps.. Rendering my 1gbps as the bottleneck.

Whereas I run av1 on the steam deck at 150mbps no 4:4:4, hdr, because any higher bit rate tends to overwhelm the VCN on amd and cause stutters and packet loss here and there.

Latency is zero concern here, I am already at like 9ms total on my moonlight setup but I would love to have 4:4:4 on amd hardware because I do notice the softness on text.

Is it pointless if I don't have a 2.5gbps Lan setup end to end?

Seems like it's only beneficial for 1440p or less.

So i built a new PC and doing a fresh windows install. On my old PC i ran apollo because when I set up game streaming for the first time i was told it was alot simplier to get everything working, I installed it and connected it to my client and everything just worked. I went with Apollo because of this reason. Ive been intrigued by VibePollo/VibeShine and was curious which one to install on my new set. I've read VibeShine is the Dev's main focus and Vibepollo exists mainly to allow people on Apollo to simply install it over there current Apollo install. Since im doing a completely fresh install should I go with VibeShine or is there a specific benefit of going with VibePollo.

I never ran Sunshine before - Apollo was the one I started with and I never tweaked the settings outside of getting HDR working.

I've been using moonlight for a while now, and I've always messed around with the host side of streaming, landing on Vibepollo that I've been using the most.

I was wondering, are there any alternatives/ forks for the client side? Anything that people think is better than the standard Moonlight, maybe some little helpful features etc.

Any suggestions are greatly appreciated. I'm mainly referring to windows. But also open to Android suggestions as well although I don't use my phone or tablet for streaming much.

Specs of the host: 9070

Specs of the client: rtx 2050

Client used: streamlight

Host used: punktfunk

The recent developments in punktfunk is honestly awesome im never going above 2-3ms of host processing latency

Tho the client for punktfunk is a little glitchy at times streamlight is a decent alternative for it but the native client only supports pyrowave and hdr.

Either way im happy with these results it’s the closest to being native.

Any tips or advice or anything i can do better is much appreciated always looking to improve

After trying out multiple handhelds and tablets. I finally found my endgame. This Lenovo Y700 Infinite is the ultimate entertainment machine. It can handle everything from native gaming to eye popping pc streaming with the oled screen.

Haven’t seen people reviewing/posting this tablet. Feel free to drop your questions if you have.

My host is on CachyOS with Polaris in Host Virtual Display mode. I'm on Bazzite for my client and using the flatpak version of Moonlight and it's a pretty old laptop with an Nvidia Quadro m1000, so h.264 is the only codec available. The host is wired and the client is the only device connected to my wireless access point, running on a clean channel. The maximum latency I was seeing in 6.1.0 was 4-7 ms.

Since I updated to 6.2.0 the frame queue delay skyrocketed, somewhere in the ballpark of 7-20 ms and I'm assuming that's causing more microstutters which are being attributed to network jitter. VSync and frame pacing are off.

Has anyone else noticed this? I see most people are pretty happy with the new changes in 6.2.0 but I haven't been able to see what others are. I decided to move back to the appimage of 6.1.0 and will stay there if it works for my setup, not a big deal. I was just curious if others were running into this, too.

ChloroFrame is an almost mac native swift based sunshine client. The 1.6 release adds experimental support for PyroWave, (Themaister's intra-only wavelet codec built for very low latency ) because why not

Details

• GPU decode in about 1.3 ms (4:2:0) to 2.4 ms (4:4:4) on an M4 Pro at 3024x1890.
• 4:4:4 chroma and 10-bit HDR10.
• a lost frame recovers on the very next one, and frames missing a few packets are still shown. This means that if a frame is lost the prior frame is repeated and the stream recovers after on its own since all frames arive as keyframes
• Uses about 280 to 400 Mbps, so it's LAN only.
• PyroWave does not work with Sunshine and Apollo. This will only work for hosts that advertise PyroWave like VibeShine.

Setup

1. Run a Vibeshine host with PyroWave enabled, ideally on Ethernet. Read the vibeshine guide on pyrowave first.
2. Use an M1 or later Mac, on Ethernet (or you can try 5/6 GHz Wi-Fi but be warned there will be a few lost frames)
3. Install ChloroFrame, pair the host, then pick PyroWave in Settings.
4. Click "Test network" in the app list, then launch.

Things to keep in Mind:

• This is Experimental still! and needs a lot of testing! There is room for a lot of refinement in ChloroFrame. The codec itself is very young. So keep this in mind when using PyroWave
• Expect a few lost frames per minute on Wi-Fi. "Test network" option often flags jitter on Wi-Fi even when the stream looks fine.
• H.264, HEVC and AV1 are unchanged.

Ethernet testers especially if you can provide some feedback that would be awesome

Download: https://github.com/AmanBhardwaj25/ChloroFrame/releases/tag/v1.6-alpha

I have an LG C2 tv that we’ve been using for years. In light of all the spyware news, I was hoping to turn it into a dumb tv and use some ‘box’ for our app needs and being able to use Moonlight reliably.

I was waiting for the new release of Apple TV but they’ve really dropped the ball with it. 60Hz, no audio pass-through, and now also a listening shitty AI machine.

Anyone have recommendations on what I could use? Something that plugs into my TV, allows me to use my surround system, and controller(s).

Hi guys,

I'm on CachyOS for 3 days and so far I'm loving it - it's very slick, the hermes agent works much faster than on Windows and games performance is top notch.

I'm having a little problem though - on Windows I used to stream from Vibepollo to Moonlight on the TV. I've tried installing Pollaris but unfortunately the TV was not able to install Nova as a client - it's a pretty old LG TV.

I've installed Vibepollo in the meantime but IDK if i've done something wrong but this app is very persistent in staying in my system. I've tried stopping the process with sudo but all I'm getting is the error saying that the process cannot be stopped safely. Because of that, I cannot install sunshine as it's being marked as incompatible.

(1/4) Safely stopping Vibepollo before package replacement error: could not safely quiesce the existing Vibepollo host (failed step: vibepollo_select_upgrade_kill_mode); package replacement is blocked. error: the old host was not stopped; admission may be closed. Retry the upgrade after fixing the failed step, or reboot to clear runtime fences.

Can anyone help me with this please?

What's a good choice of laptop to record 1080p60fps at 15-25k bitrate (or stream at 8k bitrate) while connecting with moonlight to my gaming/editing server locally via ethernet (or wifi when on the go) and other homeserver stuff (like navidrome) on top of some basic web browsing + discord on the side?

Having USB-C charging would be amazing, OLED would be HUGE but even if not I will be connecting a second monitor at home that's OLED if the main screen isn't. Solid battery life is a huge plus and a camera is a must for zoom calls.

Currently have a thinkpad t480 which is decently close to what I need but it can't handle the recording portion of things (at least when i have it running with fedora). Closest it gets is 720p60fps and even then it struggles quite hard.