whenever i use the keychron m4 wired it keeps freezing, when it does its for about a second at a time, it doesnt matter which cable, or usb port, ive tried in all 3 of my usb 3.1 port(i have a laptop without any usb2 port) and i tried on my usb c thundervolt 4 port. ive tried with and without the battery in the mouse, ive alread done a firmware update, and i already checked if it was the mouse going to sleep or if it was some form of power saving on my system, the only way hte mouse works is 2.4ghz (havent tested bluetooth) and on 2.4ghz it doesnt matter what usb port ruling out usb 3.1 interference.

oh and when it freezes then comes back the cursor catches up as if the motion i had done was cached, i also tried on a different laptop running windows and still the same issue and when it did disconnect it didnt play disconnect sound or anything.

im on arch and here are the error the mouse gave when running sudo journalctl -kf

Oct 15 20:27:10 a1cr kernel: usb 3-1: device not accepting address 67, error -71
Oct 15 20:27:10 a1cr kernel: usb 3-1: WARN: invalid context state for evaluate context command.
Oct 15 20:27:10 a1cr kernel: usb 3-1: new full-speed USB device number 68 using xhci_hcd
Oct 15 20:27:10 a1cr kernel: usb 3-1: Device not responding to setup address.
Oct 15 20:27:10 a1cr kernel: usb 3-1: Device not responding to setup address.
Oct 15 20:27:11 a1cr kernel: usb 3-1: device not accepting address 68, error -71
Oct 15 20:27:11 a1cr kernel: usb 3-1: WARN: invalid context state for evaluate context command.
Oct 15 20:27:11 a1cr kernel: usb usb3-port1: unable to enumerate USB device
Oct 15 20:27:28 a1cr kernel: linuwu_sense: CUSTOM FAN MODE (MIXED)!
Oct 15 20:27:28 a1cr kernel: linuwu_sense: Fan speeds updated: CPU=50, GPU=50
Oct 15 20:27:39 a1cr kernel: usb 3-1: new full-speed USB device number 69 using xhci_hcd
Oct 15 20:27:39 a1cr kernel: usb 3-1: New USB device found, idVendor=3434, idProduct=d040, bcdDevice= 1.15
Oct 15 20:27:39 a1cr kernel: usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Oct 15 20:27:39 a1cr kernel: usb 3-1: Product: Keychron M4
Oct 15 20:27:39 a1cr kernel: usb 3-1: Manufacturer: Keychron
Oct 15 20:27:39 a1cr kernel: input: Keychron Keychron M4 as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.0/0003:3434:D040.005C/input/input124
Oct 15 20:27:39 a1cr kernel: hid-generic 0003:3434:D040.005C: input,hidraw2: USB HID v1.11 Mouse [Keychron Keychron M4] on usb-0000:00:14.0-1/input0
Oct 15 20:27:39 a1cr kernel: input: Keychron Keychron M4 as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.1/0003:3434:D040.005D/input/input125
Oct 15 20:27:39 a1cr kernel: hid-generic 0003:3434:D040.005D: input,hidraw3: USB HID v1.11 Keyboard [Keychron Keychron M4] on usb-0000:00:14.0-1/input1
Oct 15 20:27:39 a1cr kernel: input: Keychron Keychron M4 Consumer Control as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.2/0003:3434:D040.005E/input/input126
Oct 15 20:27:40 a1cr kernel: input: Keychron Keychron M4 System Control as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.2/0003:3434:D040.005E/input/input127
Oct 15 20:27:40 a1cr kernel: hid-generic 0003:3434:D040.005E: input,hidraw4: USB HID v1.11 Device [Keychron Keychron M4] on usb-0000:00:14.0-1/input2
Oct 15 20:27:40 a1cr kernel: hid-generic 0003:3434:D040.005F: hiddev97,hidraw5: USB HID v1.11 Device [Keychron Keychron M4] on usb-0000:00:14.0-1/input3
Oct 15 20:28:07 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:07 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:13 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:13 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:17 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:18 a1cr kernel: usb 3-1: device descriptor read/64, error -71
Oct 15 20:28:18 a1cr kernel: usb 3-1: device descriptor read/64, error -71
Oct 15 20:28:18 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:18 a1cr kernel: usb 3-1: device descriptor read/64, error -71
Oct 15 20:28:18 a1cr kernel: usb 3-1: device descriptor read/64, error -71
Oct 15 20:28:18 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:18 a1cr kernel: usb 3-1: Device not responding to setup address.
Oct 15 20:28:19 a1cr kernel: usb 3-1: Device not responding to setup address.
Oct 15 20:28:19 a1cr kernel: usb 3-1: device not accepting address 69, error -71
Oct 15 20:28:19 a1cr kernel: usb 3-1: WARN: invalid context state for evaluate context command.
Oct 15 20:28:19 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd
Oct 15 20:28:22 a1cr kernel: usb 3-1: reset full-speed USB device number 69 using xhci_hcd

My first 3D-printed fingertip grip mouse, designed and modeled entirely by myself!

I used the internals from a VXE R1 SE and took inspiration from the Lamzu ORCUS.

The final weight is 45g.

For my next project, I'll try making an even smaller mouse!

Thanks for checking it out!

Just leaving this here.

Another program that silences faulty mouse switches—which tend to release and re-press the button multiple times—allowing you to keep using your broken mouse instead of throwing it away and buying a new one.

It has no graphical interface, nor does it provide any notification that it is running. If you wish to terminate it, you must do so via the process manager.

It is written in C using the Windows API and is compatible with Windows 95 and later versions; a 64-bit version is also available.

Its file size is 4KB.

ey everyone!

I'm looking for a 3D-printable lightweight replacement shell for the Endgame Gear OP1 8K V2.

I want to keep the original shape and dimensions as close to 1:1 as possible, just with a lighter shell.

What I'm looking for:

• Full-size original OP1 shape and dimensions
• Compatible with the stock OP1 8K V2 PCB and internals
• A complete replacement shell, not just a lightweight base
• STL or 3MF files that I can print myself
• Definitely NOT a mini, fingertip, or smaller version

I've seen a few lightweight OP1 mods, but most of the files I could find are either mini versions or just base replacements.

Does anyone know of a publicly available model, have files they're willing to share/sell, or know someone who could make one?

I'm also willing to pay for the STL files or commission someone to design the shell.

Any help would be greatly appreciated!

Didn't want to charge my Delux m800 mini so I made a custom usb cable with 32 awg cables then removed the battery. Weight went down to 37 grams, now feels extra floaty.

Here’s a breakdown of each components’ weight reduction:

• Outer Shell — 11.06g to 7.47g
• Inner Skeleton — 7.94g to 5.92g
• Main Buttons — 7.50g to 5.11g
• Side Buttons — 1.23g to 1.04g
• Scroll Wheel — 1.91g to 1.15g
• Base — 8.36g to 1.96g
• Battery — 4.77g to 2.43g
• Haptics — 3.48g

The scroll wheel is moddo’s Lite Scroll Wheel.

From using my X2 before this, I found I preferred playing with the haptics turned off. So for this mod I decided to remove the haptics entirely. Heads up, this does not impact the magnetic field of the HITS, only the tactile feedback you get when using the main buttons. My initial goal was to hit 35g while maintaining a (mostly) full sized, solid shell.

For the shell’s finish, I started with a 1000 grit sandpaper and worked my way up to 5000, then lightly buffed it with a microfiber cloth. This gave the shell its shiny look that is smooth when rubbing your fingers over it, but still sticks to my fingers during use. I was originally planning to add grip tape, but will be holding off as I’m pleasantly surprised with the current texture.

You can see in the last picture the weight reduction I did to the inner skeleton and the insides of each mouse button. Because I opted to remove the haptics entirely, this freed me up to also trim out the housing the haptic motors sat on.

I don't know how to put the Xraypad Obsidian Air dot skates on my Incott 029 mouse and I have an Mousepad Atk 99g Xsoft Green. The photo on the right is as it originally came.

Hi everyone, i'm making 2 mods that will get posted on cults3d and wanted some opinions on the holes pattern design. Both mods will include 3 versions (holes including clicks, holes only in the back of the shell, no holes). Shapes are inspired and not 1:1.

Scyrox v8/v8s mod:

Op1 shape upsized to 124.62 x 64.33 x 38.76

Forward sensor

35.38gr with dot skates and grips

Atk f1 v1/v2/v3 mod:

Egg xm2 shape inspired, size 124.63 x 67.04 x 38.55

Centered sensor

32.56gr with donut skates

Weights are in petg.

This mods where not made with the intent of going "super light" (since atk F1 and scyrox v8 are already really light) but more with the intent of having some shapes design at a weight that i never tried before, i've always wondered what the op1 feels like for people with small hands so I upsized it for my hand, and i wanted to try what a more forward sensor would feel like, so i made this scyrox mod. For the other one i just made the xm2 shape for the lightest PCB i own, so I could try what a light xm2 shaped mouse would feel like

So i'm making this post to ask what you guys think about the holes patterns, at first i thought i liked the triangle pattern i made on the scyrox mod but i don't like it anymore, instead i could do the standard triangle pattern like ipi float or something else if you have any recommendations. For the atk circle pattern I like It a lot but i still want to know what you guys think, since it's a really easy thing to change.

I hope to post the scyrox v8 next week, i sent the files to different testers and i'm waiting to get some opinions to change the last things.

my palm gets really sweaty during sessions and i use my finger tips to micro adjust like push the mouse inward to controll recoild in cs2 and its hard to play i use the superlight 2 right now its so like really grimy and sticky so i cant micro adjust . what mouse do you recommend me trying?

I was wondering if there is any tech savvy wizard out there who can make this mod but for a op18k v2? Iasked the original owver of this how much i could pay them but no response

https://www.printables.com/model/1385951-kabrio-fingertip-mouse-mod-for-mad-r

Hey, I’m looking for a 3d printable base mod for the a9, and if anyone knows the A9 lineup, is the base compatible with the a9 air.

I want to mod my base A9 and try make it work with the a9 air and have the a9 air stock base too instead of modding it directly.

if the zen 8k mini (5% smaller viper v3 pro) hurts the left side of my palm is it a tension issue or a shape issue or possibly both?

if it is a shape issue should i buy a pulse 2.0 (lighter op1 8k) with v1 internals?

Hey everyone, I'm looking for recommendations for a good gaming mouse under $100 CAD. I have Pachydermodactyly, which affects the shape and size of my fingers, so finding a comfortable mouse can be difficult for me. I'm looking for a mouse with well-positioned side buttons that are easy to reach and press, with enough space around them for my fingers. I don't really like mice where the left and right click buttons stop before the edge, like the Logitech G Pro X Superlight. I prefer a design like the Glorious Model O, where the left and right click buttons extend closer to the edges. I mainly want a mouse that feels comfortable, has a good sensor and low latency for gaming, doesn't have a hollow case like the Model O, and preferably has two side buttons that are practical for my thumbs. Wireless would be nice, but wired is fine too. My budget is under $100 CAD, and I'd appreciate any recommendations. Thanks!

ROCCAT was retired as a brand in 2024 and Swarm II doesn't really support my Kone AIMO Remastered anymore, so I wrote my own settings app. It's free, open source, and unofficial.

What it does:

\- DPI stages, polling rate, sensitivity, angle snapping

\- Lighting: effect, speed, brightness and the color of all 11 LEDs, with a live preview on the mouse

\- Every button on the normal and Easy-Shift layers

\- All 5 profiles, backups, and a check at login that the mouse hasn't lost its settings

\- Settings are stored in the mouse itself, so they work on any PC without the app running

It also has a Blender page (shortcuts and macros), because I'm a 3D animator and built it for my own workflow. Ignore it if you don't use Blender.

Things to know:

\- Only tested on my own Kone AIMO Remastered (USB ID 1E7D:2E2C). Other models aren't supported.

\- The exe isn't code-signed, so Windows SmartScreen will warn you. Source is on GitHub if you want to check it or build it yourself.

\- It never touches firmware, and it saves a copy of your mouse's original settings the first time it connects.

\- Not affiliated with Turtle Beach or ROCCAT.

Download and source: [https://github.com/Valencia33/Kone-AIMO-Config\](https://github.com/Valencia33/Kone-AIMO-Config)

Feedback and bug reports are welcome, especially from anyone with the same mouse.

Estou tendo um problema com o mouse que eu já tentei de tudo e não consigo resolver, Ele parece um mouse fantasma na tela, pois o cursor se movimenta, e quando passa por cima de algum aplicativo em vez do aplicativo ficar mais claro mostrando que o mouse ta em cima, não acontece nada e também não consigo clicar com ele. Mas esse bug passa temporariamente quando eu aperto as teclas “Ctrl+Alt+Del” ou quando eu aperto o botão lateral do mouse ou o scroll mas depois de um tempo ele volta. E quando jogo valorant no meio da partida aparece o cursor do mouse piscando. Já troquei de mouse e não resolve também

This is my first mouse mod I’ve ever done and I think it turned out pretty good! (Could be a little cleaner) Didn’t save much weight (55g-51g) but it was a fun little project and there isn’t really much else I can do to reduce weight on this mouse. I’ve also tried to find posts on here or videos on YouTube of people modding this mouse but there seems to be none as of now