I just had my first OSHA inspection. The compliance officer asked a floor worker to show him the SDS for the product on the worker's bench. The worker walked to the binder, flipped through it for three minutes, and couldn't find it. The officer wrote it up. The citation wasn't for not having the SDS. We had it. It was in a different section of the binder under a slightly different product name. The citation was for the SDS not being "readily accessible" to the employee during their work shift. Now I'm wondering what "readily accessible" actually means. Is there a time standard? Does digital access count? What else do inspectors check beyond just whether the SDS exists?

How does your employer ensure your safety or compensate for risks you encounter when entering someone's home. I work as a mobile crisis counselor and often go into homes with infestations or when a patient is verbally or physically agressive. I have also had coworkers assaulted by patients and workers compensation deny their claims. My employer expects us to use our personal cell phones and transportation, we do not have GPS tracking. We do complete a pre-visit screening and can go with a buddy or the police but put patients have lied and we have no written protocol.

We have a two story bank barn (think: stereotypical photo of red barn in country) that has electric but is not insulated or heated.

We're having a child's birthday party on the upper level this weekend, and are going to get unlucky with the cold front coming through. 70 the day before, 49 and wind the day of.

The event is only for three hours, and the barn itself protects against wind and rain, just looking for a little help with heat so that older and younger folks are not uncomfortable.

I asked my mechanic uncle, who said that any electric space heaters would be a waste. He offered me a torpedo heater of his which he said was confident would put off enough heat. But he also called it "the cancer cannon" and said "sometimes it lights things on fire".

The space that folks will be in will be approx 750 sq. ft; the overall size of the barn is much larger because it has four bays that are each ~15'-30' with stereotypically tall ceilings.

I have considered the torpedo heater running on the lower level, since that is all stone and concrete save for the beams, and hoping some heat rises up to the party on the second level. I have a trap door that opens up into the upper level.

I have also considered a dyna-glo indoor kerosene convection here and a bigbuddy propane indoor heater.

I don't need a lot of heat, but I need safe heat. If there is no true safe option for a few hours indoors (there are windows and sliding doors etc.), then I would rather have us just go cold than risk burning down the barn. Really appreciate any help you can provide.

Hi everyone,
I’ve recently been offered a process worker job in a plastic manufacturing factory. I believe the role mainly involves packing finished plastic products.
I’m concerned about the potential long-term health risks, particularly exposure to plastic fumes, microplastic dust and chemicals that may increase cancer risk.
I’d really appreciate hearing from anyone who has worked in a plastic manufacturing factory.
Is working in this environment safe in the long term?
Are plastic fumes and microplastic dust common in these factories?
Is there an increased risk of cancer from working in this industry?
Is packing finished plastic products generally safer than working directly with plastic moulding machines?
I’m interested in the job but worried about the possible health effects of working there for several years.
I’d really appreciate any advice or personal experiences. Thank you!

I’ll go first. Watched this guy try to save 3 seconds by jumping down from the bed of a pickup instead of using the tailgate step, landed right on an uneven chunk of broken asphalt, and rolled his ankle so badly he needed a boot for six weeks. Completely avoidable, purely caused by rushing.

The Occupational Safety and Health Administration (OSHA) published a proposed rule in the Federal Register on April 6, 2026 that would change the fixed ladder fall protection requirements in section 1910.28 of its Walking-Working Surfaces standard. 

The standard currently sets a deadline of November 18, 2036 for equipping fixed ladders that extend more than 24 feet above a lower level with a personal fall arrest system or ladder safety system. OSHA proposes removing that deadline. Ladders with cages or wells could stay in use until the end of their service lives. Any new ladder, and any replaced section of a ladder, cage or well, would still need a fall arrest or ladder safety system. OSHA says the change would cut retrofit costs and fit the long service life of fixed ladders. 

This is a proposal, not a final requirement, and it applies in the United States only. OSHA held a virtual hearing on August 24, 2026 and final written briefs from hearing participants are due October 8, 2026. As of October 2, 2026, OSHA's rulemaking page lists no final rule. 

A fixed date is easy to audit. "End of service life" depends on someone deciding a ladder is worn out.

If you've had to make that call on a site, who made it and what did they base it on? 

Source: OSHA, Deregulatory rulemaking (https://www.osha.gov/deregulatory-rulemaking)  )

Federal Register notice: https://www.federalregister.gov/documents/2026/04/06/2026-06578/walking-working-surfaces 

The ceiling in front of the bathrooms and vending machines, thats accessible to the public keep in mind, has been like this for weeks at this point. I'm ready to call osha given the ceiling collapses and power goes out every drizzle of rain.

Dans notre travail, on voit régulièrement des échelles et des escabeaux encore utilisés malgré des défauts qui pourraient devenir dangereux.

Cette courte vidéo montre pourquoi l’inspection et l’entretien des équipements de travail en hauteur sont importants.

Quelques points qui reviennent souvent :

• état des barreaux et montants
• patins et pieds
• rivets et fixations
• corde et mécanismes
• étiquettes et identification
• état général de l’équipement

Le but est surtout de sensibiliser les entreprises et les travailleurs à vérifier leurs équipements avant qu’un incident arrive.

S.O.S. Échelle Inc.

https://reddit.com/link/1x2ihjb/video/52x644wrtnuh1/player

i’ve been looking into industrial safety barriers for separating pedestrian walkways from forklift traffic and protecting equipment in busy work areas. i came across options from global industrial, vestil, and troax, but i’m not sure what differences matter most beyond the basic dimensions and materials.

for those who’ve dealt with these setups, what do you usually prioritize when comparing barriers? impact resistance, ease of installation, visibility, or how easy they are to replace if damaged?

I’m a safety specialist at a company in a state where recreational marijuana is legal. My company does not do random drug tests. Instead, they only drug test in the event of reasonable suspicion or post-accident. Under these circumstances, would it be safe for me to smoke occasionally? I’m so anxious that somehow policy will change, but we would also lose the vast majority of our working population if they actually did regular random drug tests. Looking for thoughts, advice, and suggestions.

(Cross posted from r/SafetyProfessionals)