When and Where to Use a Portable Travel Router

On Deco x5000

How do you reach these speeds if the LAN ports are both on gigabit/1000 mbps

It just makes no sense why they write 5gbps on the box? Its not like I can use them without using lan port atleast on the main pod?

How could one even *theoretically* reach 5gbps if the input port that brings internet from the modem/ont is limited to 1gbps?

I have Deco x55s - a set if 3. I have used them for years at my old house snd never had an issue. I just moved and I have one of them in my garage (about 35-40 feet from the nearest deco, which is NOT the main deco) and it is functional, I have a pc and a nas hooked to it and I can connect to them. However - ever since I hooked them up, I am having MAJOR instability on the network. I can run a speed test and get 500 down and 15 ping, and then 5 min later the speed test freezes part way through and has 0.01 mbps upload with 500 ping. It is very inconsistent and is definitely impacting my TVs and their streaming. Is this something with my ISP at the new house or is it related to the deco being on the edge of range and all the focus of the decos is on that? Does anyone have experience with this and/or advice? (Obviously i know I could just not have one in the garage, but I do enjoy having part of my setup out there)

Hey everyone having a weird issue where my router has just shut itself off and when I power cycled it all it did was flash the power light at me now. I have tried holding the reset button on the back for 30 seconds and I’ve power cycled several times, I am using the original power adapter that came with it. Any ideas on what to do?

And yet TP-Link is still banned from selling their new routers in the US. Yes, TP-Link, per the FCC and Federal courts , it is considered a ban.

My router is Archer AX11000 (Firmware Version: 2.2.1 Build 20250725 rel.9119(5553) - Hardware Version: Archer AX11000 v2.0) and extender is RE815X (Firmware Version: 1.0.3 Build 20260528 rel.45228(5553) - Hardware Version: RE815X v2.0). Why my router's 5G-2 is not working? Both router and extender are updated to latest firmware. Bandwidth and channel settings of 5G-2 from AX11000 are at AUTO.

Just upgraded from an M4R to a BE25 and noticed that the Weekdays & Weekends was an included option in the Parental Controls and now is not.

I know that it's not going to change anything and they don't care, but it's really a simple option that shouldn't be a paid add-on, it doesn't require any cloud or active service from tp-link.

Its only purpose is to cause frustration on the user and maybe get $15 a year out of frustration. What they just got is for my next wifi devices to not be from Tplink. We shouldn't be treated like that as customers. rant over

https://www.tp-link.com/au/home-networking/range-extender/re655be/

Cannot connect or register to tp-link cloud functions. Which means I'm locked out of additional functionality of the device such as auto firmware updates, remote access etc. It can't even do a manual firmware check as it just times out too. Had to update it manually the old fashioned way.

I just bought this thing, so if they've taken the servers offline permanently and therefore bricked all these devices, it would be good to know so I can quickly return it.

There is nothing wrong with my internet connection, latest firmware etc.

'm trying to troubleshoot intermittent internet drops with my internet connection and would appreciate suggestions from the community.

Setup 1

• Nokia XS-010X-R fiber ONT
• TP-Link Deco BE11000 mesh system

The problem:

When using the Deco as my main router, I occasionally get an “Internet Disconnected” status and then it reconnects to the internet in a few mins. This happens a few times a day.

Setup 2

• Nokia XS-010X-R fiber ONT
• EERO Router used in Bridge Mode
• TP-Link Deco BE11000 mesh system used in AP mode

In this setup, the system is a bit more stable and I observed the internet dropped only once and then reconnected a few minutes later.

i have had the DECO system and the EERO exchanged and I still have the same issue.

I'd like to understand how to resolve this issue

A few questions:

1. Could this be related to WAN DHCP, gateway detection, or the Deco's internet connectivity checks?
2. Could a firmware issue cause intermittent internet disconnections on the system
3. Is there a way to determine whether the Deco is actually losing its WAN connection or merely reporting an internet connectivity failure?
4. What logs, settings, or diagnostic tests should I check the next time this happens?

I would prefer to identify the root cause rather than simply use the eero as a workaround.

Has anyone experienced similar behavior with the Deco BE11000, particularly when connected directly to a fiber ONT?

I have raised this with TPLINK Support and they exchanged the deco system for me, but I still have the issue

I've set the router to use the address given to me but I'm still having problems with ublock seeing me, I'm using my deco as router. has anyone gotten it to work properly?

I got problem with Tapo d210. It suddenly disconnected from the apps and when I try to reset it by removing it on the apps and hold the reset button for 5 seconds, now it keeps blinking red and white followed by a long oranges and it wont connect anymore. Anyone have the same problem ?

Tengo un TP Link Extender que funciona durante un periodo de tiempo pero luego se cae el internet solo y en unos minutos regresa, a veces se cae más seguido, a veces no se cae, el periodo que demora en llegar al internet también varía, y la frecuencia que pasa durante el día también varía.

Ya eh probado la mayoría de los métodos que aparecen en Youtube y internet en general. Tengo el Tplink a una buena distancia del router principal, lo tengo colocado perfectamente bien, en zona alta y en el medio de la casa como dice algunos vídeos, lo eh reiniciado y reestablecido de fábrica tantas veces que no recuerdo, lo eh enlazado y desenlazado del router principal y nada. Ya no se que voy hacer.

Ayudaaaa

I have 5 deco x55. I was using 4. 3 bought together and 2 bought used from someone else. I put one of the used one in the garage and the other just kept. About 2 months ago the WiFi started getting flaky. After days of troubleshooting it became apparent the original main was going bad and going on and off line. I replaced it with the spare one I bought used and left the others in place. Now it appears to be randomly dropping as well. Tonight it randomly turned yellow. I unplugged and replugged and it’s working again. Do I have to buy new decos?

Hi everyone, I recently moved into a new house and I got an Archer BE6500 router and a 1gig download speed internet plan. Setting it up was super easy and I had no issues, it runs great and the download speeds are insanely fast downstairs, but when I was doing some speed tests upstairs in my room where I have my computer I went from getting 1.1gig download all the way to 200mb/s. Our only coax cable to connect to the modem is in a small cutout under the stairs, so I imagine the signal is having a hard time going through all of that. I am wondering, would getting a mesh extender or a powerline kit be the better option? I'll admit I'm not very smart when it comes to WiFi and I'm not quite sure how mesh works yet, wouldn't the signal still have a hard time getting to the extender? And for powerline do they create their own hotspot or do you have to wire into them with Ethernet to get the benefits? I would like to get some of the download speed back, I know getting it perfect won't be very obtainable, so please let me know what you would recommend! Thank you!

I'm experiencing a strange issue with Windows 10 that I have never experienced before. When downloading multiple files, my internet connection is lost. The same issue happens when deleting files from any folder and from recycle bin.

I'm using the T4U Plus USB Adapter. I previously had the T4E PCIe Adapter and was experiencing the same issue (reason why I changed the Adapter).

Windows gives no errorlogs at all, updating and downgrading drivers for the adapters didn't change the result.

The issue started happening out of nowhere. I thought the connection lost was due to poor signal/quality of the adapter. After testing it by downloading/deleting figured out that it was related to that.

USB Tethering with my phone makes the issue go away, but it's not a solution for the issue.

The issue might've happened after a Windows Update, can't really tell. This seems to be the only cause I could find. After installing the USB adapter, I checked the Windows Updates and I had one for a RealTek driver that modified the driver for the adapter. Reverting the driver only caused the RealTek driver to re-install and the internet "freezes" continue to happen.

Other devices connected to the network don't experience the issue.

If there's any information required to help me, please ask. I'm lost on what I can do further besides a reset of my installation.

Thank you in advance.

Hi. I am logged in but I am stuck here, I have entered my email and password which didn’t work I used the router (hb410) assigned password to see if that worked but I still can’t progress through the app setup. Help me please and thank you :)

Ciao a tutti,

condivido un problema critico di instabilità sulla mia rete Deco BE65 nella speranza di un riscontro dal team TP-Link o da chi ha un setup simile.
Ho un ticket ufficiale aperto dal 20 luglio 2026, ancora senza soluzione.

Configurazione:

• Router principale: Deco BE65 (v2.0, Router Mode)
• Firmware Deco BE65: 1.3.3 Build 26072712 Rel. 60761
• Nodi: Topologia mista (BE65, X50-PoE, X50-Outdoor) su backhaul Ethernet 2.5G/1G
• Client: ~80–90 dispositivi (alta densità domotica a 2.4 GHz: Shelly, Homcloud/Tuya, Google Nest)
• Impostazioni: Rete IoT 2.4 GHz attiva; Mesh Roaming (802.11k/v) disattivato sui device fissi.

Problemi riscontrati e analisi log:

Dopo periodi di uptime stabile, la rete collassa e il BE65 master crasha riavviandosi da solo.
Dai log di sistema emergono anomalie precise:

1. Crash con Wi-Fi 7 (Pixel 10 Pro XL): Appena il mio Pixel 10 Pro XL si aggancia alla rete Deco negoziando le bande MLO/Wi-Fi 7, il demone di steering Qualcomm va in tilt generando errori continui bloccando il bridge e facendo crollare la connettività.
2. Saturazione 2.4 GHz: Picchi costanti di 98% di airtime occupato con oltre 1,5 milioni di errori TX
3. Trigger del crash (DHCP Loop): A causa dei beacon e pacchetti persi a 2.4 GHz, i dispositivi smart perdono temporaneamente la connessione e inviano continue raffiche di discovery. Il demone esegue una scansione sequenziale dell'intero file lease per ogni singola richiesta generando un loop sincrono infinito che porta la CPU al 100% (Load Average > 4.4) fino al riavvio forzato per watchdog kernel

Tentativi già effettuati (senza successo):

• Rete IoT 2.4 GHz dedicata.
• Roaming mesh disattivato sui tutti client fissi.
• Pixel temporaneamente isolato su altra rete per non far cadere il Deco.

Richiesta a TP-Link:

Visto il ticket aperto da mesi, è prevista una beta firmware che corregga il buffer overflow (gestione MLO/Wi-Fi 7) e ottimizzi la gestione/caching dei lease su per evitare crash da tempeste DHCP?

Qualcuno ha trovato un workaround?

Hi, I installed a Deco XE70 Pro last week to replace the router my fiber provider provided free for one year and I now have to rent. I updated the firmware on the three units upon installation. All of my devices, about 30, connect to my network just fine. My issue is there are some devices that won't talk outbound, so their apps are unusable. Specifically, my Emporia EVSE for my EVs and various LG appliances. I'm aware that IoT can be a challenge, but the EVSE is from 2024, some of the LG from 2025, and they all work fine on my fiber provider's router. From what I've seen, these Decos are a bit limited in configuration options, however, I have confirmed that all of these devices are on 2.4 GhZ. I've tried forcing them on 2.4, disabling things like beamforming and device isolation, however my semi-limited knowledge tells me those are really ideas for lack or weak connectivity to the home network, which I have no problems. Any ideas? TIA.