What's it called or do they sell a base for this? Attaching a pic of my Makita

I am trying to find one that can do it all, i will be working on my fk1 civic and light household stuff, i searched far and wide but can’t quite find the one i need, i’ve seen that the m18 line mid-torque is what i should need but i’m open to advice.
Thanks in advance 😁

Does this kit ever go on sale? I’ve been eagerly waiting for it to be on sale for a long time, but unfortunately, I haven’t been able to find it.

would appreciate some help thank you.

Bought the M12 impact and hammer drill on sale last week and went to use the drill for the first time today.

Hammer drill that came with the kit had the selector collar from the regular drill driver. Still worked but only while hammering through all the clutch settings.

Thought I was losing my mind until I compared it to my co-workers.

Correct label and part number.

Anyway Home Depot exchanged it without too much hassle. They seemed stumped as well.

2k ft lbs of torque with forge battery. 10 tires per 8.0 forge battery. Will this make the bigger 1 inch obsolete?

Anyone know anything about this? Restock chance or is it an accident?

I have the 3/8s with the hog ring, and have had issues (right out the box) with sockets not fitting tight. Figured I’d try the detent pin for the 1/2” and my god, what a pain in the ass it is. Main 2 issues: when impacting a very tight/stuck bolt, I literally have to pry the socket off the base with a screwdriver or pliers. 2nd and most annoying, I have to use a pick or something to actually release the detent just to change the socket. Anybody else run into these issues? FYI, using Milwaukee impact sockets…

Not sure if anybody else has mentioned, but check out your local Home Depot every now and then. Found this pack of 2 for about $20 which is what 1 of them cost alone if I’m correct.

The app has this same set for about $43 so I don’t know what’s going on, but checkout will ring you out at about 20 bucks.

Just something to keep an eye out for y’all!

Is this deal worth jumping on or are there better deals often? Ive been tracking these for a while at $599 tool only. That 8.0 forge with charger are no cheap bonus plus those safety glasses.

Internet # 318241585
Model # 2734-21-48-73-2010
UPC Code # 888234584486

For those of you wondering, it arrived as advertised.

Hey all,

Recently I've been seeing 6 amp hour M12 batteries for less than the 5 amp hour batteries on eBay​. I've heard the conversations regarding how "well and beloved" these batteries truly are. Okay. Seriously, I've heard nothing but bad talk about them here on Reddit. I've also heard that it depends on the tool whether or not they're worth anything or not.

So my question is this, do they work well in the M12 job site fan? What's t​heir runtime on settings one, two, and three? Recently I was helping with a fair booth, where I needed the fan for about 12 to 14 hours per day. I currently have three 5.0ah HO batteries, two 4.0ah XC batteries, one or two 3.0ah and two of the 1.5ah smaller batteries.

The price I've been seeing on Ebay for lots of 2 6.0ah batteries is about $70-80. Their rating number is over 1k, so I'm guessing they're not scamming. If anyone's used these batteries in their fan, can you please let me know if they're worth that, or should I wait for more 5.0ah HO batteries to go on sale again? Thanks for your help, and have a good rest of your week!

Peace,

A dork behind the keyboard

Looking to grab the m12 bandfile but never see it go on sale. Anyone know if it get daily deal on HD? Or maybe black friday?

Hard to pass at this price so grabbed one. Curious if anyone has actually used and what thoughts were on it.

Hey all,

Some context... I'm not a professional but I'd like to get more DYI around my house. I currently need to replace trim, some sheet rock, and a pallet board decorative wall in my basement. I bought an M18 angled finish nail gun along with an M18 hackzall. I also grabbed an M12 circular saw and an M12 multi tool. I hacked the circular saw and the hackzall with HD using the tips from this forum, thanks everyone!

I need a little more advice though. I have a Makita impact driver, but at this point I'd rather stay in the Milwaukee system seeing as all my other tools are there. I don't have a drill.

I saw this deal and it looked really good after a hack, but I'm wondering if for my purposes I should wait for the fuel surge to go on sale? I rarely do large lag screws, but if I do I could create a pilot hole so I figured the more precision and reduced noise of the surge would make sense.

Also Black Friday is around the corner, but I figured this kit at the hacked price will likely not be much lower.

Any thoughts? Thanks

​

Hi all

I was going to buy the M12 FIR38G2 rachet but seen that the new M12 FIR38L2G2 long reach rachet is now out so im unsure on which would be better.

Will mainly used for suspension work, servicing and occasionally some DIY engine work.

Any advice on which one i should go for as budget only allows me to buy one.

I bought these and they’re great. Sound quality is good, ear protection is great when in the right mode. The only issue I have is getting the mic to pick up. I got it working for a little bit earlier today when I disconnected them and reconnected them. They worked for one phone call, then the next phone call the mic stopped picking up again. Not sure if it’s an Apple software issue or what. I had the same issue with some JBL earbuds a while back so I quit using them. Then ended up getting these for the ear protection and realized that it had the same mic issue.

What’s the pack out case that hold the M18 2967-20 1/2” High Torque Impact Wrench with the XC5.0 battery?

And

Which one for the M12 1/2” stubby with the 5.0 battery?

Thanks!

I just bought the M12 FUEL 3/8” Stubby, and I was wondering what impact sockets do you recommend (not necessarily only Milwaukee). I hear things about Tekton, Quinn, Icon, Gearwrench, etc. I want to be able to have all sizes, but I don’t need luxury. What are quality ones that you recommend?

I’m wondering whether or not the mushy direction selector detent is common in this impact or did i get a bad QC unit? When i go to hit forward on selector it has no positive click or detent but hitting it in reverse it’s a little better. The slop i can live with but not being able to feel the positive detent and having to push in further just to get it in forward direction doesn’t feel right.

Please

Purchased 12/25/24 but when I went online to start a warranty claim this was the response I received. Does anyone know if the zippers are covered on the packout coolers?

Base cover is getting worn on my jig saw, the M18 2737-20 (D-handle jig saw). Replacements are cheap but seems like something one could 3d print.